Any good IKEA tabletops for a standing desk? : r/ikeahacks - Reddit
网页2021年4月10日 · While its as bit longer than what you are looking for, it is one of the few desk-tops that Ikea carries that is solid wood. I have currently sanded, stained, and will be finishing mine with poly. Side-note, Gerton will stop being sold in July, and you can snag one in an Ikea for $79. Reply. rhvvan.
List of common IKEA desks for PC setups: - Reddit
网页2020年5月9日 · Glasholm / Alex. Kullaberg. Malm. Arkelstorp. Bekant. Ekbacken. Saljan. Idåsen. Here is the complete list of the most common desks used, though the Karlby and Linnmon are the most popular choice.
Best table top? : r/IKEA - Reddit
网页2023年4月8日 · If you're deadset on getting a table top from Ikea get the Karlby, but if you're willing to do maybe an hours worth of work buying a counter top and some sealant from Home depot would a better bang for your buck alternative. I am a student looking for a durable (ideally wood) Ikea table top to sit on two Alex drawers.
Best table top for desk? : r/IKEA - Reddit
网页2021年5月25日 · Some ideas: If you plan on cutting it I would go with gerton, Karlby, eckbacken in that order. Gerton is solid wood. Karlby is a layer of wood glued to an mdf base, they call it "thick veneer", so it can go through a light sanding if scuffed/scratched maybe a couple times depending on how much you take off. Eckbacken is laminated mdf …
I just discovered Ikea no longer sells the Linnmon corner desk top, …
网页2023年4月1日 · Another thing you may be able to do is to go to a furniture store or a specific office furniture place and sit down at a few display desks (if possible) with a curve to test it, and if you like it, have some large cardboard or paper with you to put on top of the curve and trace the line of the curve on its underside, also making an X at the ...
ikea - solid table tops? : r/buildapc - Reddit
网页2023年4月26日 · Depending on budget, GoStand in the UK do a brilliant job, have been using one of their standing desks with a 2 monitor arm clamped and my desktop PC on top of it. It is solid, great choice, but a little pricier at £600 compared to the £41.50 on the Ikea setup previously. 1. Reply.
Table top suggestions for dual monitor arm : r/IKEA - Reddit
网页2021年3月25日 · If your span is more than 3 feet, regardless of the top you get, please get a center support leg. Alternatively, bolt an angle iron or steel strut channel to the bottom of the table from end to end width-wise. Otherwise you will encounter sag. Maybe not today, maybe not tomorrow, but someday. 8.
Question about Lagkapten top : r/ikeahacks - Reddit
网页2021年9月22日 · Lagkapten tops will definitely sag over time if it doesn't have any underside reinforcement/support. The tabletop is comprised of a fiberboard (aka MDF)/honeycomb structure which doesn't convey "strength" in my opinion. As for mounting hardware to fiberboard, sure it'll work but from my experiences, it's a "set it and leave it" scenario as ...
Topped off my IKEA setup with a Flexispot E5 - I love it!
网页2021年7月25日 · chopper_sheep. No no, I meant that you rise it up the same way as on the 2nd pic but just a tad bit, so that the distance between the tabletop and the top of the drawers is 5-7cm. So while other people raise it with for example the capita legs that they put on top of the drawer, you'd do it with the stand. I'm just courious how would it look!
Screwing into Ikea Linnmon tabletop : r/ikeahacks - Reddit
网页2021年9月21日 · Have the plate fixed somehow, hold the power drill firmly, start at its slowest setting and move up and down, this should make a nice cavity in your honeycomb. Remove the tool and use a syringe to fill that cavity Completely with epoxy. Then you can drill the final hole for the screw. In short: it is not worth it. 3.